ã€Abstract】According to the intensive rain, snow and freezing weather in Guizhou, Hunan and Chongqing, the Central Meteorological Observatory issued a short-term weather forecast at 8 pm yesterday. It is expected that in the future, due to restrictions on Indian peninsula and South Sea steam transportation, frozen weather will not continue to eastern China. The expansion of the area, the occurrence of a wide range of low-temperature rain, snow, and freezing weather in early 2008 is less likely. The Central Meteorological Observatory issued a short-term weather forecast at 8:00 a.m. on the freezing rain, snow and ice weather in Guizhou, Hunan, and Chongqing. It is expected that the frozen weather will not continue to expand in the eastern part of China due to the restrictions imposed by the Indian peninsula and the South China Sea. The possibility of large-scale cold weather, snow, ice, and freezing weather at the beginning of 2008 is less likely. On the morning of January 1 this year, the first freezing rain began in central Guizhou, and by the morning of the 2nd, the scope of frozen rain reached its maximum. Frozen rain weather occurred in 70 counties (cities, districts), 65 counties (cities), and southeastern parts of Chongqing. At 8 o'clock on the 4th on the 4th, a total of 67 counties and cities in Hunan Province had appeared frozen. Among them, the thickness of ice-covered wire in Jingzhou County of Huaihua was as high as 13 mm. There are still 59 counties and cities in the south of Xiangxi and Xiangzhong that have not yet been eliminated. Ice has been strengthened. The Central Meteorological Observatory estimates that in the coming week, there will be intermittent freezing of rain in Guizhou, the western and southern parts of Hunan, and the northeastern parts of Guangxi. The time will be concentrated from the 5th to the 7th and the 9th to the 11th. The Central Meteorological Observatory also stated that although the weather process took place earlier, the scope of influence was relatively concentrated, mainly affecting Guizhou, Hunan and Chongqing. According to the provincial division of power grids, Guizhou and Guangxi power grids belong to China Southern Power Grid, and Hunan Power Grid belongs to the State Grid. Since the freezing weather was concentrated in the management of the Southern Power Grid, China Southern Power Grid initiated the “I-level warning of red, rain and snow disasters (red)â€. Since the current rain and snow and freezing disasters are weaker than at the beginning of 2008, relevant sources of the National Grid told reporters yesterday that they have not yet launched the highest-level emergency response. In addition to rain and snow and freezing weather, the winter season in central China will also be subject to the test of coal supply. Over the past few years, in the winter and spring, electricity shortages in the region have become the norm. As of December 15 last year, coal inventories in Hubei Province had fallen below 1.8 million tons, and the distribution was uneven. The total power of coal-fired power plants and shutdowns of main thermal power plants reached 2 million kilowatts. The power supply situation in the province is very severe. From December 20 last year, the province initiated the province's coal and electricity transportation coordination yellow emergency plan to coordinate coal supply and demand. According to the latest data from the Hubei Provincial Economic and Information Commission, on January 4, the total 14 coal-fired power plants in the province were 1.572 million tons. The situation is still grim. In order to cope with the above situation, the State Grid Corporation of China will take out 1.5 million kilowatts of interregional swaps in January this year to support Central China Power Grid, including 500,000 kW of Three Gorges additional power, 1 million kW of UHV AC, and 500 kV of Depot DC.
Larger size workpiece require larger capacity and increased rigidity in order to support heavier table loads. TipTop's Bridgecenter Double Column Machining Centers are designed for extreme cutting capacity, offering the benefits of high speed and high torque spindle options, spacious work envelopes, and patented double column bridge type design. Standard linear scale feedback and taper spindle configurations make it suitable for the mold industry where high levels of accuracy are needed in roughing and finishing large cavities.
Gantry Machining Center,Gantry Type Machining Centers,Bridgecenter Double Column Machining Centers,Gantry VMC Jiangsu Sailing Intelligent Equipment Co., Ltd. , https://www.sailingcnc.com